Progress at last - coolant hoses and brakes

Well headed out to the garage with a job list this weekend. Did have a bit of a fiddle around last weekend, but did not really achieve anything significant. Main job was grinding away a little of the cross member so the radiator would lay a little flatter, and making up the front brackets for the radiator

First task was sorting out the radiator hoses and connections. I had got a 45 degree bend to connect to the top of the radiator which needed trimming to keep the overall height down. Looks like it will fit OK under the nose cone, but will need to do a quick check at some point. I then tidied up the relief hose connection from the thermostat unit and made a bracket to support it. Can be seen here through the exhaust.


I then modified the old coolant tube from the previous radiator install to add an additional inle to take the return from the header tank. I used the bend I had cut off the above tube as it already had a swaged end.


I have fitted it using a cut off 45 degree rubber hose and an old 90 degree silcone hose - the bend is tighter than 90 degrees so have ordered a 135 degree bend. The original hose I was going to use for this I discovered was narrower in the middle of its run compared to the ends, so would not fit onto the 32mm tube. Grrrr. You can see one connection has been made to the return unit, the other to be sorted once the location of the header tank is sorted out.

Finally, decided to have another look at the brakes. All the options I have come up with for forward mounted master cylinders still get in the way of any inlet system. So I decided to have another look at the Zero brake system. With a bit of adjustement of the angle of the master cylinder mounting plate I THINK I can create enough clearance to the steering column. I have cut a base plate for it using the original mounting holes for the previous pedal set up, and clamped the new unit to it.


Tomorrow I am going to cut the master cylinder mounting bracket off and tack weld it back on at a slight angle. Hopefully this will lift the master cylinder just far enough away from the column so I can get the brake pipes connected.

Going backwards

Why can't people manufacture stuff correctly? After the farce of the pedal box, it now appears the plenum is also a pup. The injector holes are too small and also badly aligned so the injectors will not go in, the angle it puts the fuel rail at makes it contact the rocker cover, and the plate for the throttle body is distorted so can't seal it very easy. A quick internet search showed I was not the first to run into problems with this unit. I have emailed the supplier requesting a refund so will see how I get on.

So what did I achieve today. I removed the old expansion tank, repositioned the horn, and sorted the throttle body bracket so it did not hit the bonnet, but that may now be a waste of time as I will have to sort some other inlet system. Grrrrrr.

Radiator Part 2

So with the test piece suggesting it would fit, I ordered a new Polo radiator from Fleabay.

On initial offering up of the rad suggested it should be OK. A friend Matt popped round to help fit it today, and kept me focussed when I could easily have given up.

The main problems were a) keeping the rad clear of the steering column and b) when doing that not preventing the bottom hose connection of the rad being blocked by a chassis cross member.

The first bracket arrangment we came up with was sturdy but set the radiator too high and would have prevented the nose cone being fitted. We went through various set ups but eventually settled on one which used flat plate and a couple of angle brackets as the main support, and will add some upper brackets to make it firmer. I will be able to vent the majority of the air out of the top of the nose cone, so should reduce a fair bit of engine bay temperature.

Radiator Part 1

The Air Flow meter once mounted on the throttle body with a 90 degree bend was coming into contact with the top of the radiator. I had wanted to get the radiator tilting forward so I could vent it out of the top of the nosecone to reduce engine bay temperature.



So I stripped the front end out to have a fresh start at the radiator set up. The original one had always been a compromise of Robin Hood supplied parts.

So this is before (less the cooling fan that was in front)


And this is stripped out.....


So I made up a cardboard template of a VW Polo radiator and used it to see if it would fit.

More problems, a few solutions.

Sorry for the lack of updates, no excuses......

Its being a nightmare. This is the sort of period during a full build where cars end up as 'unfinished projects' on ebay. So what particular walls have I run into?

Brake Pedal Conversion

Once I got the Zero brake kit aligned it became obvious the brake lines would collide with the steering column and its mounting bracket.


This is the unti without the master cylinder attached. A possible solution is to use a shorter master cylinder which may give more clearance.

Another alternative I am looking at is to move the old pedal mounting plate back to either create space for a very shor master cylinder (such as Fiat Punto) or to have a cross bar move the master cylinder across to miss the new plenum.

Injectors/fuel rail.

Lined up the fuel rail and injectors on the new plenum chamber. Initial problem is the fuel rail comes into contact with the rocker cover, especially the vent tube from it. Due to the design of the chamber it angles the injectors backwards. I have looked at fuel rails off later Mondeo's but believe these are from Duratec engines rather than Zetec so unlikely to fit. Going to email the seller (Pepper Performance) for advice.

Radiator

See next post.....

More bits coming off

Not been a good day in the workshop......

Having discovered last week the new pedal set won't fit have had to come up with alternative solutions, then to add to it the inlet system wont fit without having to move the radiator.

Will update more later in the day......grrrrrrrrr

Parts ordered

Well got onto ebay today and ordered a pump, swirl pot and 12mm fuel pipe. Hopefully should have most stuff to put the injection side loosely together over the forthcoming weekend.

Have made a deal with myself that if I complete the pedals and injection by the end of February, I will do the bulkhead/scuttle conversion.